Suffolk Original Pre Finished Internal Door
£125.00 ex VAT - (£150.00 inc VAT )
 |
| In stock - Delivery Calculated at Checkout |
 |
| Next Day & Standard Delivery to UK & NI |
 |
| Available For Single Order |
 |
| Need Advice? Call 01646 687064 |
Special Delivery Information
Estimated Delivery Time – 1 Week
Description
XL Joinery Suffolk Original Pre Finished Internal Door
A real timeless design the Suffolk is a 6 slat boarded door from the Classic Oak Collection. This door combines deep u-grooves and real oak veneer to create a truly distinctive looking door that would not look out of place in any property. This range is extremely extensive and also includes supporting glazed and fire doors in many different sizes.
Top features
- Engineered construction for added strength, stability and performance
- Product supplied unfinished, ready to paint or stain
- A-Grade American White Oak Veneer
- FSC Certified product with full chain of custody
- Deep u-groove design with real Oak Inlays
- Real Oak Lipping allowing for 15mm each edge to be trimmed off the door
Additional Information
Additional information
| Weight | 0.40 kg |
|---|
Installation Options
Installation
- Reversible
- Yes
- 30
- 15
- 15
- 15
- 65mm
- Light sanding using 240g sand paper
- 3
- 3″ Butt
- Good Quality Woodstain, Paint or varnish suitable for engineered, Veneered timber doors utilising D3 adhesive beneath the veneer.
HANDLING AND STORAGE Doors should always be stored flat, ideally in the same room where they are to be installed. Protect the door from damp and dirt by leaving it in its protective packaging until ready for finishing and fitting. Doors should not be fitted where extremes of temperature or humidity may occur, e.g. in a newly plastered room or near a sauna. In new build situations the doors should only be fitted when the property is ready for final decoration. INSTALLATION When trimming a door to fit, 15mm can be removed from each edge of the door to a maximum reduction of 30mm in both the height and width. Any reduction must be removed evenly from each edge of the door, e.g. to trim your door by 8mm in width, remove 4mm off each side. Three hinges should be used to hang all doors, to prevent warping or bowing. Latches and locks should not be fitted adjacent to door mid-rails where the joint may be compromised. All hardware screw holes should be pre-drilled to prevent splitting of the timber. FINISHING Doors will require a light sanding prior to finishing using a fine grade sandpaper (grit number 240 or 320). All timber surfaces should be fully finished. Failure to treat all the timber surfaces may lead to excessive changes in moisture content which will cause the timber to shrink or swell, possibly causing splits and distortion. Please refer to the finish manufacturer’s application instructions for further details. DO Use a good quality paint, stain or varnish suitable for veneered doors. Apply first coat of finish immediately after unpacking doors from protective packaging. Apply coats equally to all faces and edges including the top and bottom of the door. Use the same number of coats for lock, latch and hinge cut-outs. DO NOT Use oils, wax, dyes or preservative treatments Use thinned/mixed paints or stains. Mix incompatible products, e.g. paint on one door face and stain on the opposite face. MAINTENANCE To prolong the natural beauty of your door regularly clean the surface with a damp cloth. If the finish appears to fade after a few years simply apply a single coat of finish to renew its lustre.
Please note:
- Because all doors are manufactured differently, please follow the individual instructions that come with each door to ensure you do not void the manufacturer’s guarantee.
Maintenance Guide
Technical Specification
Product Specifications
- Hand-matched premium quality Oak Veneer
- 20mm Oak lippings on all 4 edges of standard doors. Fire Doors have 11mm Oak Lippings
- XL Joinery V-Groove Oak inserts
- 6 Vertical Panels (24” and 626mm wide door has 5 panels/ 21” and 526mm door has 4 panels/18” door has 3 panels)
- Ready for Stain or Paint
- Available in a wide range of sizes, glazed and fire doors including Metric and Imperial Sizes.
- Can be hand finished with XL Colours
- Available Made to Measure with XL Bespoke Service
- FSC Certified product
- Engineered construction for consistent strength and stability
- High screw holding strength to ensure secure fitting of hinges, latches and handles
- American White Oak Veneer
- American White Oak lippings and inserts
- Particleboard Core
- Thickness: 35mm
This internal door has no glazing, ensuring privacy and making it the perfect option for bedrooms and bathrooms.
Natural Oak and Oak effect internal doors are a popular choice as they can perfectly match almost any decor theme. Both timeless and on-trend, oak doors are a great choice to endure changing fashions.
2ft3
Full Size: 1981 x 686 x 35mm (27″)
Height (mm): 1981
Width (mm): 686
Thickness (mm): 35
Width (inches): 27″
Weight (kg): 28 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Panels: 6
2ft6
Full Size: 1981 x 762 x 35mm (30″)
Height (mm): 1981
Width (mm): 762
Thickness (mm): 35
Width (inches): 30″
Weight (kg): 34 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Panels: 6
2ft9
Full Size: 1981 x 838 x 35mm (33″)
Height (mm): 1981
Width (mm): 838
Thickness (mm): 35
Width (inches): 33″
Weight (kg): 37 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Panels: 6