Suffolk Essential P10 Unfinished Internal Door with Clear Etched Glass
£130.00 ex VAT - (£156.00 inc VAT )
 |
| In stock - Delivery Calculated at Checkout |
 |
| Next Day & Standard Delivery to UK & NI |
 |
| Available For Single Order |
 |
| Need Advice? Call 01646 687064 |
Special Delivery Information
Estimated Delivery Time – 1 Week depending on quantity ordered, subject to warehouse stock.
Description
A contemporary glazed door that allows lot’s of natural light to flow through the home. The etched glass design complements the existing Suffolk door family whilst maintaining a decorative feature that creates a stunning focal point.
This product is also available in…
✔ Unfinished ✔ Fully Finished ✔ Clear Glass
Additional Information
Additional information
| Weight | 0.40 kg |
|---|---|
| Dimensions | 35 cm |
Installation Options
- Yes
- 30
- 30
- 15
- 15
- 15
- 65mm
- Light sanding using 240g sand paper
- 3
- 3″ Butt
- Osmo door oil, high solid 3060 or 3033. Good quality waterbased clear varnish. Good Quality Interior Paint.
- HANDLING AND STORAGE Doors should always be stored flat, ideally in the same room where they are to be installed. Protect the door from damp and dirt by leaving it in its protective packaging until ready for finishing and fitting. Doors should not be fitted where extremes of temperature or humidity may occur, e.g. in a newly plastered room or near a sauna. In new build situations the doors should only be fitted when the property is ready for final decoration. INSTALLATION When trimming a door to fit, 15mm can be removed from each edge of the door to a maximum reduction of 30mm in both the height and width. Any reduction must be removed evenly from each edge of the door, e.g. to trim your door by 8mm in width, remove 4mm off each side. The protection film on the glass should not be removed until painting or staining has been completed. Three hinges should be used to hang all doors, to prevent warping or bowing. Latches and locks should not be fitted adjacent to door mid-rails where the joint may be compromised. All hardware screw holes should be pre-drilled to prevent splitting of the timber. FINISHING Doors will require a light sanding prior to finishing using a fine grade sandpaper (grit number 240 or 320). Use masking tape when finishing glazed doors to ensure that the finish does not go on the glass. All timber surfaces should be fully finished. Failure to treat all the timber surfaces may lead to excessive changes in moisture content which will cause the timber to shrink or swell, possibly causing splits and distortion. Please refer to the finish manufacturer’s application instructions for further details. Once you have completed finishing the door, remove the masking tape and the protective film from the door. To remove the film simply take a craft knife and cut around the entire glass aperture, ensuring the corners have been cut. Finally, peel off the film from the glass surface to leave a smooth finish. DO Use a good quality paint, stain or varnish suitable for veneered doors. Apply first coat of finish immediately after unpacking doors from protective packaging. Apply coats equally to all faces and edges including the top and bottom of the door prior to final fitting. Use the same number of coats for lock, latch and hinge cut-outs. DO NOT Use oils, wax, dyes or preservative treatments Use thinned/mixed paints or stains. Mix incompatible products, e.g. paint on one door face and stain on the opposite face. MAINTENANCE To prolong the natural beauty of your door regularly clean the surface with a damp cloth. If the finish appears to fade after a few years simply apply a single coat of finish to renew its lustre.
Please note:
- Because all doors are manufactured differently, please follow the individual instructions that come with each door to ensure you do not void the manufacturer’s guarantee.
Maintenance Guide
Technical Specification
Top features
- 20mm lippings
- Beautiful etched glass
- Engingeered construction for strength and stability
- Hand matched oak veneers
- Available in Colours by XL
- The Oak Essentials
Specifications
- Suffolk
- Unfinished
- Oak
- Glazed
- Yes
- Oak
- Natural
- Dowelled
- Oak veneer
- Particleboard
- Engineered
- Yes
- 5mm safety glass
- Clear etched
- Toughened
- (2013 version): Part K amalgamates the now defunct Approved Document N,The glass is toughened to either BS6206 / BS 6262 Part 4 or BS EN12150 and BS EN 12600 as stipulated in Approved Document K of the Building Regulations
- D3
- Yes
- Lipped on all four sides
- Hardwood
- 20
- 20
- 20
- Yes
- Solid white oak
- 0.6
T
2ft3Full Size: 1981 x 686 x 35mm (27″)
Height (mm): 1981
Width (mm): 686
Thickness (mm): 35
Width (inches): 27″
Weight (kg): 32 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Glass Style: Clear Etched Glass
2ft6
Full Size: 1981 x 762 x 35mm (30″)
Height (mm): 1981
Width (mm): 762
Thickness (mm): 35
Width (inches): 30″
Weight (kg): 32 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Glass Style: Clear Etched Glass
2ft9
Full Size: 1981 x 838 x 35mm (33″)
Height (mm): 1981
Width (mm): 838
Thickness (mm): 35
Width (inches): 33″
Weight (kg): 35 Approx.
Family: Suffolk
Collection: Classic Oak Collection
Finish: Unfinished
Texture: Natural
Material: Oak
Location: Internal
Use: Internal Door
Glass Style: Clear Etched Glass