01646 687064

Oak Floors Online

Account

Log In
Create New Account
Lost Password

Our Location


Contact us

Shopping Basket

0 £0.00 (ex VAT)

View Basket

A Local Family Run Flooring Business Based In Pembroke Dock, Pembrokeshire - Showroom

15(4)x70x350 UV Oiled Herringbone Oak Flooring H2011B
15(4)x70x350 UV Oiled Herringbone Oak Flooring H2011B - Image 2

15(4)x70x350 UV Oiled Herringbone Oak Flooring H2011B

£41.50 ex VAT per m2(£49.80 inc VAT per m2)


Required Packs - (1.96m2 m2 per pack)

How many packs do I need?

Enter the size of your room below to work out how many packs you will need.

Please note - pictures are for colour reference only (lengths / sizes can differ)

Order a SAMPLE sent via Royal Mail, Evri or Fedex.

* Free sampling is available on many of our products, the more you order, the smaller the piece will be due to postage box sizes.

Free Sample

How To Compare The Samples You Receive

Dyfed Waterproof SPC - Manafactured by Oak Floors Online
Next Day & Standard Delivery to UK & NI
Call For Free Samples
Need Advice? Call 01646 687064

 

 

Brooks Bros
Next Day & Standard Delivery to UK & NI
Free Samples
Need Advice? Call 01646 687064

 

 

Description

15mm Thick Boards, 4mm Oak Wear Layer, 70mm Width, 350mm in Length Engineered Oak Flooring – H2011B

Our new narrow width range of Herringbone formation Engineered Oak Floor boards. Perfect for creating a stunning patterned floor, which is a great modern look. A smooth UV Natural Oiled finish will go with any room and furniture.

Installation & Maintenance

Glued down method and is suitable for installation above UFH.

Details of all these methods can be found in our Fitting Guidelines guide.

This product is suitable for installation over UFH, as long as its surrounding conditions are maintained and controlled as required. 

The multiply back construction of our Engineered Oak flooring provides much greater stability than Solid Oak when subjected to varying levels of heat, humidity, and moisture. This also enable the boards to be manufactured a lot wider than solid without risk of cupping, which is associated with the wide solid oak boards available.

This stability allows the floor to be installed as a floating floor where conditions permit, directly onto concrete or timber subfloors, and is ideal for floating floor installation over an underlay that can provide your floor with extra protection from possible moisture attack from beneath.

Engineered Oak can also be fitted above underfloor heating when the correct installation guidelines are followed and the necessary levels of heat, humidity and moisture are maintained by the owner after installation.

We can supply a Self-Regulating UFH System that’s perfect for use with our Oak Flooring because it never overheats, making it safe and super energy efficient.

IMPORTANT NOTE:
Sometimes the plywood backed engineered boards will seem as if they are ‘bowed’ from end to end when they are first removed from the packaging. This is very common with a plywood backed product because of the difference in molecular structure of the solid oak face and the plywood backing.

It is not a fault with the board and should be expected. It does not cause any problems during installation because of the required staggered joint fixing for an oak floor. Obviously as each board is ‘surrounded’ when fixed, by at least another 4 boards, it is straightened and aligned perfectly every time. In fact, some fitters claim this actually strengthens the floor further.

 

Delivery Information
Although our engineered products have an underside of high quality plywood and are designed to provide extra stability after installation, they’re still constructed of all natural products.After proper and sufficient acclimatisation, the conditions during installation should be maintained as consistently as possible thereafter for optimum performance and to avoid dimensional movement of each board within the finished floor.
For information on important, ongoing maintenance, please refer to our Care & Maintenance guide.
Weather, Humidity, Temperature and the Ongoing Maintenance of Your Flooring  
Because oak is a natural, hygroscopic (water absorbent) material, and its dimensions are directly relative to its moisture content, we must control and maintain the relative humidity within our homes to enable the moisture content of our oak flooring to remain constant. This will ensure stability of each board within the finished floor, because failure to do this may force these boards to change dimensionally and structurally. This is not at all a fault of the flooring itself but all to do with the conditions that it’s being forced to endure.
Here’s an example of what can happen, when the outdoor temperature is 0°C
The maximum amount of water that a cubic metre of air can hold at this temperature is 5 grams, so when you bring this cubic metre of air inside and heat it to 25°C, the relative humidity drops to only 23%. We actually recommend a minimum of 40% for optimum floor stability (incidentally, this is also the level that health experts recommend for our bodies too, so good for our floor and good for us).

But it gets worse as the temperature outside falls lower, and this is why the air inside any heated building in the winter can become too dry, which can obviously have an effect on our flooring (and our bodies).

When relative humidity is allowed to drop too low, our flooring is forced to lose moisture itself and will try to curl upwards towards the dry air (similar to a piece of bacon under a grill) in an effort to find moisture.Any time the temperature outside is well below freezing, relative humidity inside will be below 20% unless you do something to increase it, and not increasing it can have a devastating effect on your oak floor.
Technical Information

Additional information

Weight 27 kg
Finish

UV Oiled
Board Thickness

Board Width

Length

350mm
Oak Wear Layer

4mm
Grade

A Grade
Moisture Content

6-9% on arrival to site.
Construction

4mm Oak on 11mm Eucalyptus plywood
Profile

Herringbone Formatt – Left & Rights, TG4: T&G sides & ends, all micro bevelled
Length Tolerance

+/- 1.0mm
Width Tolerance

+/- 0.2mm
Thickness Tolerance

+/- 0.5mm
m2 Per Carton

1.96m2
m2 Per Pallet

78.4m2
Installation Method

Glue Down, Nail/Screw Down
Suitable for UFH?

Yes
Free Sample Available?

YES
Specification

Our 15 mm Engineered Oak is constructed as a multi layer board, consisting of a Solid Oak face or wear layer of 4mm, with an 11mm plywood backing that forms the T&G, and provides a good strong underside suitable for installation by nailing, gluing or floating. The underside is also ‘sealed’ with a final stabilizing veneer.

Our Engineered Boards do not have a softwood core and because of this are strong enough to be fitted using any of the 3 common methods; Glue Down, Nail Down, or Float.

  • 15mm Overall Thickness
  • 70mm Wide
  • 350mm Length Boards
  • Single Strip Oak Face
  • ABC GRADE
  • 11mm (7-Ply) Eucalyptus Plywood Backed
  • Full 4mm Oak Wear Layer (European Oak)
  • Moisture Content 6 – 9%
  • Micro Bevelled Sides & Ends (Unfinished is also available as Square Edge)
  • TG4 End Matched
  • 1.96m2 Per Carton
  • Extra Important Detail;
    • Suitable for installation above UFH
    • ‘Thermostabile’ Adhesive Provides Maximum Strength Between Plies
    • Sealed Underside for Improved Moisture Protection (reduces risk of ‘cupping’ after installation)
    • Extra Stabilising Veneer to Underside (extra stability after installation)
    • Very Accurate Machining Tolerances for Fast & Simple Fitting (saves on fitting costs)
    • Angled T&G Joint for Excess Adhesive (reduces risk of excess adhesive reaching the surface)
  • All our flooring products are machined to very accurate machining tolerances for fast and simple fitting.
  • Length Tolerance: +/- 1.0mm
  • Width tolerance: +/- 0.2mm
  • Thickness Tolerance: +/- 0.5mm

You May Also Need...

SKU: H2011B Categories: , , , , Tags: , , , , , , , , ,